Size: 20 g

Directions

To adhere frags, colonies, or for general aqua scaping, first test fit the item to be glued onto the site it is to be adhered. Note the contact points the item has with the site. Retrieve the item and, while not submerged, place a small amount of glue on each site contact point. Quickly fit the item onto the site again. A skin will form over the glue upon contact with water. It is helpful to break this skin slightly while in contact with the site. Hold the item down for about 15 seconds (more in areas of strong flow). Check that the item is secure. Repeat as necessary in order to build up a small amount of glue for a more secure hold.

Directions

Beginner
Use 2.5 mL (half a cap) for each 160 L (40 US gallons) twice a week or as needed in response to signs of nitrogen deficiency (e.g. stunted growth, chlorosis). For smaller doses, please note that each cap thread is approximately 1 mL.

Expert
The beginner dose raises nitrogen by the same degree that 1 mg/L nitrate would. This dose is sufficient to provide approximately 4 g of growth (dry) or about 20 g (hydrated) over a 1 month period (assuming all other necessary nutrients are provided). For increased growth use proportionately more.

To target a specific nitrogen increase, dose according to the following formula: 0.25vn=m, where v= volume of tank in gallons, n=desired nitrogen increase (if using a “nitrate equivalent” value for “n” then use a factor of 0.05 instead of 0.25 in the formula) and m=volume of product to use in mL. For example to raise 20 gallons by 0.20 mg/L nitrogen you would use: 0.25*20*0.20=1 mL.

Because one-half of the nitrogen in Flourish Nitrogen is from nitrate you can get a reasonable estimate of nitrogen levels by doubling a nitrate reading.

The most easily obtained sources of potassium are potassium nitrate and potassium phosphate. Both of these sources add to either nitrogen or phosphorus as well as potassium, making it virtually impossible to target a specific NPK ratio. Flourish Potassium is derived from potassium sulfate, allowing the user to adjust potassium levels without affecting nitrogen or phosphorus.

Directions
Use 1 capful (5 mL) for every 125 L (30 US gallons). This dose raises potassium by 2 mg/L. Repeat 2–3 times per week or as needed in response to signs of potassium deficiency in older leaves which include: chlorosis (yellowing), necrosis (death/browning), pinholes in leaves, and weak stems and roots.

When choosing an iron supplement, it is important to know the distinction between the two forms of iron. The iron will be in one of two oxidation states: ferrous having a +2 charge, or ferric having a +3 charge. Ferrous iron, the preferred iron form and is soluble in water at any pH. Ferric iron, however, is only soluble below a pH of around 5.5; but if the pH is higher than 5.5, which more than likely it will be in a planted aquarium, the ferric iron will become insoluble and precipitate, settling in the root zone. Once this occurs, foliar absorbtion becomes impossible.

To overcome this precipitation, competing products employ a chelate of ferric iron: iron-EDTA. While this does keep it soluble, it has a couple of drawbacks with respect to foliar uptake of iron. (1) Iron-EDTA bonding is very strong, thus very little of the iron will be available to the plants over a given time frame and (2) Physiological energy must be expended by the plant in order to extract the ferric iron from EDTA-iron and then convert (reduce) it to the ferrous form. Our approach is different in that we use a complex (not chelate) of ferrous iron in Flourish Iron.

Flourish Iron is a highly concentrated (10,000 mg/L) ferrous iron gluconate supplement. Plants are able to much more easily derive a benefit from Flourish Iron because ferrous iron gluconate is already in the ferrous form so they do not expend energy reducing it. Despite what other manufacturers may intimate, gluconate is not harmful to plants or fish. In fact, ferrous gluconate is better suited to foliar feeding than is iron-EDTA owing to the relatively weaker iron-gluconate bonding vs. iron-EDTA bonding. In addition, ferrous gluconate has the added bonus of being a source of carbon.

Directions
Use 1 capful (5 mL) for each 200 L (50 US gallons) or as required to maintain about 0.10 mg/L iron. For smaller doses please note that each cap thread is about 1 mL. Use MultiTest Iron test kit to monitor iron concentrations. Due to rapid utilization, test within 30 minutes. Use as needed to combat signs of iron deficiency (usually seen in new growth) which include: chlorosis (yellowing) of tissue between veins and short and slender stems.

During the first ten to fourteen days after application, Flourish Advance works to stimulate root growth beneath the surface. After this initial induction period, significantly enhanced growth in the leaves and stems of the plants will occur.

Directions
Shake well before use. Use 1 capful (5 mL) for every 80 L (20 US gallons). Dose daily or as required to maintain plant growth.

The most easily obtained sources of potassium are potassium nitrate and potassium phosphate. Both of these sources add to either nitrogen or phosphorus as well as potassium, making it virtually impossible to target a specific NPK ratio. Flourish Potassium is derived from potassium sulfate, allowing the user to adjust potassium levels without affecting nitrogen or phosphorus.

Directions
Use 1 capful (5 mL) for every 125 L (30 US gallons). This dose raises potassium by 2 mg/L. Repeat 2–3 times per week or as needed in response to signs of potassium deficiency in older leaves which include: chlorosis (yellowing), necrosis (death/browning), pinholes in leaves, and weak stems and roots.

Directions

Beginner
Use 2.5 mL (half a cap) for each 160 L (40 US gallons) twice a week or as needed in response to signs of nitrogen deficiency (e.g. stunted growth, chlorosis). For smaller doses, please note that each cap thread is approximately 1 mL.

Expert
The beginner dose raises nitrogen by the same degree that 1 mg/L nitrate would. This dose is sufficient to provide approximately 4 g of growth (dry) or about 20 g (hydrated) over a 1 month period (assuming all other necessary nutrients are provided). For increased growth use proportionately more.

To target a specific nitrogen increase, dose according to the following formula: 0.25vn=m, where v= volume of tank in gallons, n=desired nitrogen increase (if using a “nitrate equivalent” value for “n” then use a factor of 0.05 instead of 0.25 in the formula) and m=volume of product to use in mL. For example to raise 20 gallons by 0.20 mg/L nitrogen you would use: 0.25*20*0.20=1 mL.

Because one-half of the nitrogen in Flourish Nitrogen is from nitrate you can get a reasonable estimate of nitrogen levels by doubling a nitrate reading.

When choosing an iron supplement, it is important to know the distinction between the two forms of iron. The iron will be in one of two oxidation states: ferrous having a +2 charge, or ferric having a +3 charge. Ferrous iron, the preferred iron form and is soluble in water at any pH. Ferric iron, however, is only soluble below a pH of around 5.5; but if the pH is higher than 5.5, which more than likely it will be in a planted aquarium, the ferric iron will become insoluble and precipitate, settling in the root zone. Once this occurs, foliar absorbtion becomes impossible.

To overcome this precipitation, competing products employ a chelate of ferric iron: iron-EDTA. While this does keep it soluble, it has a couple of drawbacks with respect to foliar uptake of iron. (1) Iron-EDTA bonding is very strong, thus very little of the iron will be available to the plants over a given time frame and (2) Physiological energy must be expended by the plant in order to extract the ferric iron from EDTA-iron and then convert (reduce) it to the ferrous form. Our approach is different in that we use a complex (not chelate) of ferrous iron in Flourish Iron.

Flourish Iron is a highly concentrated (10,000 mg/L) ferrous iron gluconate supplement. Plants are able to much more easily derive a benefit from Flourish Iron because ferrous iron gluconate is already in the ferrous form so they do not expend energy reducing it. Despite what other manufacturers may intimate, gluconate is not harmful to plants or fish. In fact, ferrous gluconate is better suited to foliar feeding than is iron-EDTA owing to the relatively weaker iron-gluconate bonding vs. iron-EDTA bonding. In addition, ferrous gluconate has the added bonus of being a source of carbon.

Directions
Use 1 capful (5 mL) for each 200 L (50 US gallons) or as required to maintain about 0.10 mg/L iron. For smaller doses please note that each cap thread is about 1 mL. Use MultiTest Iron test kit to monitor iron concentrations. Due to rapid utilization, test within 30 minutes. Use as needed to combat signs of iron deficiency (usually seen in new growth) which include: chlorosis (yellowing) of tissue between veins and short and slender stems.

Directions

Beginner

Use 2.5 mL (half a cap) for each 80 L (20 US gallons) once or twice a week or as needed in response to signs of phosphorus deficiency (e.g. stunted growth, plant dark green).
Expert

The beginner dose raises phosphorus by 0.05 mg/L (0.15 mg/L phosphate). The ideal phosphate level will vary, but generally ranges from 0.15–1.0 mg/L. Use MultiTest Phosphate to monitor phosphate levels. To target a specific phosphate increase, dose according to the following formula: 0.8vp=m, where v= volume of tank in gallons, p=desired phosphate increase and m=volume of product to use in mL. For example to raise 20 gallons to 0.1 mg/L phosphate you would use: 0.8*20*0.1=1.6 mL.

Size: 2 pack, 4 g each